Setting the System

Operation switch

  1. CANCEL switch

  2. RES switch

  3. MRCC switch

Operation conditions

The MRCC with Stop & Go function operates when all of the following conditions are met.

  • The MRCC with Stop & Go function is on.

  • The selector lever is in the D position.

  • The parking brake is released.

  • All the doors are closed.

  • The driver's seat belt is fastened.

  • Vehicle speed is 0 to 145 km/h (0 to 90 mph)

 

  • In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 30 km/h (20 mph) or less and “Mazda Radar Cruise Control Disabled Under 30 km/h” is displayed in the multi-information display.

    • The Forward Sensing Camera (FSC) cannot detect target objects.

    • There is a problem with the stop hold control function.

    • There is a problem with the Electric Parking Brake (EPB).

Close Note
View Note

Setting the vehicle speed

  1. Press the MRCC switch to turn the system on.

  2. Accelerate the vehicle until it reaches the desired speed using the accelerator pedal and press the RES switch up (SET+) or down (SET-) to set the speed.

 

  • When the system is turned on, the MRCC standby indication (white) turns on and the MRCC display indications are displayed on the multi-information display and the active driving display.

  • When the vehicle speed is set, the set vehicle speed is displayed on the displays and the MRCC standby indication (white) changes to the MRCC set indication (green).

  • The minimum speed setting is 30 km/h (19 mph).

Close Note
View Note

Travel status

Indication on multi-information display

Indication on active driving display

During travel at constant speed

During travel under headway control

Setting the distance between vehicles

The distance between vehicles is set to a shorter distance by pressing the CANCEL switch down, and to a longer distance by pressing the CANCEL switch up. The distance between vehicles can be set to 4 levels: Long, medium, short, and extremely short distance.

The distance between vehicles increases or decreases depending on the vehicle speed.

Distance-between-vehicles guideline

(at 80 km/h (50 mph) vehicle speed)

Indication on multi-information display

Indication on active driving display*1

Long (about 50 m (164 ft))

Medium (about 40 m (131 ft))

Short (about 30 m (98 ft))

Extremely short (about 25 m (82 ft))

  1. Displays a pop-up image in the active driving display only when the driver operates the switch.

Changing the set vehicle speed

How to change the set vehicle speed using the RES switch

When the RES switch is pressed up (SET+), the vehicle accelerates, and when the RES switch is pressed down (SET-), the vehicle decelerates.

  • Press and release immediately: 1 km/h (1 mph)

  • Press and hold: 10 km/h (5 mph)

How to change the set vehicle speed using the accelerator pedal

Depress the accelerator pedal until the vehicle speed reaches the desired speed, then press the RES switch up (SET+) or down (SET-) and release the switch.

Temporary cancellation

If any of the following conditions is met, the MRCC with Stop & Go function is canceled temporarily.

  • The MRCC with Stop & Go function operation conditions are not met.

  • The CANCEL switch is pressed.

  • The brake pedal is depressed.

  • The front radar sensors cannot detect target objects.

  • The DSC has operated.

  • The Smart Brake Support (SBS) has operated.

  • The frequency of the braking operation by the MRCC with Stop & Go function is high.

  • There is a problem in the system.

Resuming the control

If the MRCC with Stop & Go function is temporarily canceled, it will resume operation at the previously set speed by pressing the RES switch after all of the operation conditions have been met again.

Turning off the system

When the MRCC switch is pressed while the MRCC is operating, the MRCC turns off.

Page top