Child-Restraint System Suitability for Various Seat Positions Table
(Mexico)
Provided information in the table shows your child-restraint system suitability for various seating position. For installation suitability of other manufacturer child-restraint system, carefully consult the manufacturer's instructions which accompany the child-restraint system.
When installing a child-restraint system, the following points must be observed:
-
(Front passenger seat/Second-row seat)
Always remove the head restraint before installing a child-restraint system. However, when installing a backless booster seat, always install the vehicle head restraint to the seat where the backless booster seat is installed. In addition, always use a tether strap and attach it securely. Refer to How to Use the Head Restraints (Search).
-
When installing a child-restraint system to the front passenger seat, adjust the seat slide position as far back as possible. Adjust the seat bottom (height adjustable seat bottom) to the highest position so that the seat belt can securely fasten the child-restraint system.
Refer to How to Use the Front Seats (Search).
-
When it is difficult to install a child-restraint system to the front passenger seat/second-row seat, or the seat belt cannot be secured to the child-restraint system, perform the following operations to adjust the seat holding the child-restraint system so that the seat belt can be secured completely to it.
-
Move the seat forward or back.
-
Move the seatback forward or back.
-
Move the seat upward or downward. (Vehicles with height adjustment function)
-
(Second-row seat)
-
When installing a child-restraint system came equipped with a tether, remove the head restraint.
Refer to How to Use the Head Restraints (Search).
-
When installing a child-restraint system using the ISOFIX lower anchors, if the connectors of the child-restraint system do not reach the lower anchorage and the child-restraint system cannot be installed, slightly tilt the seatback of the seat holding the child-restraint system rearward. If the seatback of a second-row seat cannot be reclined due to interference with luggage on the rear seat or passengers, slide the seat forward once and then recline the seatback.
(Second-row seat/Third-row seat)
-
If the tether strap does not reach the anchor bracket, use an extension strap.
-
When installing a child-restraint system to the second-row seat or third-row seat, adjust the seat position of the front seat so that the child-restraint system does not contact the front seat.
Refer to How to Use the Front Seats (Search).
-
When installing a child-restraint system to the rear seat, refer to the How to Use the ISOFIX Lower Anchor (Mexico)/Using LATCH Lower Anchor (Except Mexico) (Search).
-
An i-Size child-restraint system refers to a child-restraint system which has acquired i-Size category certification for the UN-R 129 regulation.
|
Seating position |
Passenger |
Second-row seat (Left) |
Second-row seat (Center)*5 |
Second-row seat (Right) |
Third-row seat (Left) |
Third-row seat (Center)*3 |
Third-row seat (Right) |
|---|---|---|---|---|---|---|---|
|
Seating position suitable for universal belted (yes/no) |
Yes (UF) |
Yes (U)*4 |
Yes (U) |
Yes (U)*4 |
Yes (U)*4 |
No |
Yes (U)*4 |
|
i-Size seating position (yes/no) |
No |
Yes (i-U) |
No |
Yes (i-U) |
No |
No |
No |
|
Largest suitable rearward facing fixture (R1) |
No |
Yes (IL) |
No |
Yes (IL) |
No |
No |
No |
|
Largest suitable rearward facing fixture (R2) |
No |
Yes (IL) |
No |
Yes (IL) |
No |
No |
No |
|
Largest suitable rearward facing fixture (R2X) |
No |
Yes (IL) |
No |
Yes (IL) |
No |
No |
No |
|
Largest suitable rearward facing fixture (R3) |
No |
Yes (IL) |
No |
Yes (IL) |
No |
No |
No |
|
Largest suitable forward facing fixture (F2) |
No |
Yes (IUF) |
No |
Yes (IUF) |
No |
No |
No |
|
Largest suitable forward facing fixture (F2X) |
No |
Yes (IUF) |
No |
Yes (IUF) |
No |
No |
No |
|
Largest suitable forward facing fixture (F3) |
No |
Yes (IUF) |
No |
Yes (IUF) |
No |
No |
No |
|
Largest suitable lateral facing fixture (L1) |
No |
No |
No |
No |
No |
No |
No |
|
Largest suitable lateral facing fixture (L2) |
No |
No |
No |
No |
No |
No |
No |
|
Largest suitable booster fixture (B2) |
No |
Yes (IUF) |
No |
Yes (IUF) |
No |
No |
No |
|
Largest suitable booster fixture (B3) |
No |
Yes (IUF) |
No |
Yes (IUF) |
No |
No |
No |
|
non i-size compatible with a support leg (yes/no) |
Yes*1 |
Yes |
Yes |
Yes |
No |
No |
No |
|
lower ISOFIX anchorages but without Top Tether (yes/no) |
No |
No |
No |
No |
No |
No |
No |
U = Suitable for “universal” category restraints approved for use in this mass group.
UF = Suitable for forward-facing “universal” category restraints approved for use in this mass group.
IUF = Suitable for ISOFIX forward child restraints systems of universal category approved for use in the mass group.
L = Suitable for particular child restraints given on attached list. These restraints may be of the “specific vehicle”, “restricted” or “semi-universal” categories.*2
IL = Suitable for particular ISOFIX child restraint systems (CRS) given in the attached list. These ISOFIX CRS are those of the “specific vehicle”, “restricted” or “semi-universal” categories.*2
i-U = Suitable for i-Size “universal” Child Restraint Systems forward and rearward facing.
i-UF = Suitable for forward-facing i-Size “universal” Child Restraint Systems only.
Yes = Child-restraint system can be secured on the seat.
No = Child-restraint system cannot be secured on the seat, or there is no fixture.
X = Child-restraint system cannot be installed.
-
Child restraint system can only be installed in the forward-facing position.
-
A Mazda genuine child-restraint system can be installed. Regarding child-restraint systems which can be installed, refer to Child-Restraint System Types (Search) or the accessories catalog.
-
Three-seater type
-
(6:4 split adjustable-type bench seat type(Second-row seat) and three-seater type(Third-row seat))
When installing a child-restraint system on the center seat of the second/third-row seat, do not seat occupants in the outboard seat positions of the second/third-row seats.
-
6:4 split adjustable-type bench seat type
(Except Mexico)
-
Regarding child-restraint systems which can be installed to your Mazda, consult an Authorized Mazda Dealer.
-
It is not able to set the child-restraint system with the support leg in the rear center seat.
-
For the CRS which do not carry the ISO/XX size class identification (A to G), for the applicable mass group, the child seat manufacturer shall indicate the vehicle specific LATCH child-restraint systems recommended for each position.
